Free Download Distek Evolution 4300 Manual Programs That Help
Product Types.
REASON: The circulator is not turning on due to thermal switch reset. This occurs when the TCS pump is not primed properly.PRE-REQUISITE: Service Engineer or person performing this service must have proper training in servicing the instrument.RESETTING THE THERMAL SAFETY SWITCHStep 1. Turn off the TCS and unplug from the AC outlet prior to resetting the thermal switch.Make sure that the TCS has had time to cool down prior to resetting the thermal safety switch. This can take up to 10 to 20 minutes.Step 2. On the back of the TCS there is a small access hole where the thermal safety switch is located (As shown below).
Free Download Distek Evolution 4300 Manual Programs That Help Online
Using a non-metallic tool or the end of a pen or pencil, reset the thermal safety switch by depressing the button. You should feel or hear a click indicating that the switch has been reset.Step 3. Once the thermal safety switch has been reset, make sure the TCS has been properly primed or the thermal safety switch will trip again. Please see Priming the TCS Pump steps below. Turn on the unit and enable the heater.Information about resetting the thermal safety switch can be found on page 3-14 in the 2100C Operation Manual.Information about priming the pump can be found on page 2-6 in the 2100C Operation Manual and on page 2-8 of the EVO 6300 Operation Manual. PRIMING THE TCS PUMPStep 1. Attach a 24 inches (61 cm) long x ½ inch (13mm) ID drain tubing to drain valve.Step 2.
Raise the drain tubing to vertical position as shown. Drain valve should be tilted up.Step 3. Cover the end of the tubing with your thumb and open the drain valve. Slowly lower the tubing while slowly opening the end of the tubing allowing water to fill up as much of the tubing. Once filled, close again the end of the tubing with your thumb and raise the tubing.
Uncover the end of tubing to force water in to the pump inlet. Perform this step at least two to three times. Turn on the TCS circulator and observe that air has been purged from the pump indicating that the pump was primed correctly. If it does not, repeat step 2 and 3 until all the air is purged from the pump. The intrinsic dissolution rate is defined as the dissolution rate of pure substances under the condition of constant surface area, agitation-stirring speed, pH and ionic-strength of the dissolution medium.The knowledge of intrinsic dissolution rate is vital in screening new drug candidates as it can help optimize the physiological effectiveness of new dosage forms. Distek has improved the performance and reliability of the rotating cylinder or “wood apparatus” with the paddle over stationary disk intrinsic apparatus.
This is available in two configurations; standard for use with 1L vessel and mini for use with 100/200 ml vessels. The Distek design avoids the formation of air bubbles on the surface of the product and eliminates the potential of product “slippage” as can be the case with the wood apparatus.The Distek standard and mini intrinsic apparatus consists of steel punch, die, and base plate (fig. Figure ATest material is placed in the 0.8 cm diameter die cavity (optional cavity sizes are available) and the punch is inserted. The punch, die and press plate are placed in a laboratory press and kept under 2000 psi for 4-5 minutes. The press plate is disconnected from the die to expose a compact pellet of.5 cm2 surface area.A Viton gasket is placed around the threaded shoulder of the die and a polypropylene plastic cap is screwed onto the threads. The assembly is then immersed, pellet side up, in the bottom of a flat dissolution vessel containing 900ml of dissolution medium at 37C.
The paddle blade is positioned 6mm above the surface of the pellet and rotated at 50 rpm.See USP 30-NF 25 General Chapter page 531 for more details. The embedded temperature sensor inside each of the hollow stirring shafts allow the EVOLUTION Series to continuously control, monitor, and record the temperatures of each individual vessel throughout the entire Dissolution test.
Located inside and at the bottom most position of the shaft (red arrow below), the temperature sensors are able to continuously monitor the temperature of the media. Without the use of an external thermometer it eliminates any associated hydrodynamic effects. The EVO 6100 and EVO 6300 are the only dissolution systems on the market with this capability.The shafts of the EVO 6100 and EVO 6300 are designed for 100% assurance that the medium temperature is maintained throughout the entire test. Also, it eliminates the need to remove the shaft when changing between apparatus 1 (baskets) and apparatus 2 (paddles) thanks to the use of detachable stirring elements and the height adjustment block. Cipher instrument control software is a Windows based application designed and developed by Distek to remotely access and control our dissolution equipment.Cipher can be installed locally or networked providing full access to any Distek dissolution bath and autosampler from any appropriately connected PC running the application. Cipher allows the user to create and run methods, monitor instrument status, generate reports, and control users and manager logins. Cipher also offers the flexibility to set the level of security appropriate for your laboratory.
When enabling all the security features and combined with the appropriate internally developed policies, Cipher will meet 21 CFR part 11 compliance. Cipher currently controls the Model 2100C, EVO 6100, 6300, and 4300. Distek’s 2100C water bath-based dissolution system (pictured below) is known for being durable and user-friendly. However, your clients may not be aware of the versatility and customization that the 2100C offers.
When configured at the time of the order, the Distek 2100C has the ability to support up to eight 2L vessels or four 4L vessels. Also, with the quad stir (pictured below) or the single station small volume kit the 2100C can support 6 to 24 positions at 100ml or 200ml.Please note that an existing system cannot be upgraded to 2L/4L capabilities.